Showing 1–21 of 93 results

Filter
  • Fix It Sticks ALL-IN-ONE TORQUE DRIVER KIT

    Fix It Sticks ALL-IN-ONE TORQUE DRIVER KIT FISMUTK

    $165.00 Add to cart

    Fix It Sticks All-in-One Torque Driver Kit

    Featuring the Fix It Sticks All-in-One Torque Driver.  Tighten down your scope rings, mounts, actions screws, etc. while in the field, at the range, or at home.  No more over or under tightening your critical components.  Lightweight and compact – the All-in-One Torque Driver Kit will always be there when you need it.

    Kit includes:

    • All-in-One Torque Driver (15 – 65 inch lbs)
    • T-Way T-Handle Wrench
    • 15 different bits: T10, T15, T20, T25, [hex 3/32, 5/64, 1/8, 5/32, 3/16, 2.5mm, 3mm, 4mm, 5mm], P1, slotted #5
    • 1/2″ Socket and 1/4″ bit adapter set
    • Zippered case with Molded Holder

    Please note that the All-in-One Driver operates differently than our Torque Limiters.  For instructions and instructional video, please click here.

  • Fix It Sticks Single Bits

    $3.99 Select options

    1″ Long, 1/4″ Bits.  Electroless Nickel Finish

     

     

  • Fix It Sticks Bubble Level Set

    $69.99 Add to cart

    Level your optics with machined aluminum levels, featuring precise UK-sourced bubble vials

    Kit includes:

    • Magnetic level
    • NATO/Pic rail level/anti-cant device
    • Protective foam carrier with pouch

     

  • Fix It Sticks Scope Jack

    $50.39 Read more

    Fix It Sticks Scope Jack

    A new way to level your optic, the Fix It Sticks Scope jack works with any 1/4 inch driver to quickly and easily level your scope to your NATO/Pic rail.

    Just mount the scope jack to the NATO/pic rail under your scope and turn the drive handle until the lifting arm engages with the flat section under your turrets.  Once the scope is level, maintain pressure while tightening your ring screws to keep optic level throughout the process.

    Requirements:

    • Works with any scope with a flat section under turrets
    • Needs a minimum of 1/4 inch clearance between NATO/Pic rail and scope
    • NATO/Pic rail must be accessible under optic
    • In cases of minimal clearance, it may be necessary to remove the thumb screw and clamp, then slide the Scope Jack onto the rail from the side and reassemble.

    Integrates perfectly with Fix It Sticks Replaceable Edition and T-Way Driver.

  • Fix It Sticks 700 Bolt Opener

    $29.99 Add to cart

    Access your Remington 700 firing pin quickly and easily in the field with our compact custom bit.

    Remington Bolt Opener

    Levers the firing pin head with a “bottle opener” action
    Molded synthetic polymer bushing protects bolt plug from damage
    Metal ¼” Hex Base allows it to work with any ¼” driver
    Integrates perfectly with Fix It Sticks T-Handle Drivers.
    NOTE: Fix It Sticks/T-handle Not Included

  • Fix It Sticks EXTENDED ACTION BITS 3/16″

    $11.99 Read more

    Custom ball end hex bit designed to tighten hard to reach screws.

     

    • Choose 3/16″ for Remington 700, AICS, etc.
    • Choose 5/32″ for Ruger 10/22 V-Block, etc.
    • Choose 1/8″ for KIDD, etc.
    • Shaft of bit is 0.1875″ X 4.0″ long for hard to reach screws.
    • Works with any standard 1/4″ bit driver

    Integrates perfectly with Fix It Sticks Replaceable Edition for field / travel use.

    Integrates perfectly with T-Way Wrench for shop use.

     

  • Fix It Sticks RATCHETING T-WAY WRENCH

    $59.00 Read more

    Description

    It’s Fix It Sticks’ versatile T-Way Wrench with a ratcheting feature added for faster tightening and loosening of fasteners, even in tight spaces. The Ratcheting T-Way Wrench has magnetic holders on all three ends that accept any standard 1/4″ bit.This versatile tool is a great addition to your firearms toolkit, for carrying in your vehicle and so many other uses.

  • Sale! Fix It Sticks Pin Punch Set

    Fix It Sticks Pin Punch Set

    $23.19 Add to cart

    Fix It Sticks Pin Punch Set

    Set of Six Pin Punches designed to integrate with the Fix It Sticks System.

    Pin Punches are in the following sizes:

    • 1/16″
    • 3/32″
    • 1/8″
    • 5/32″
    • 3/16″
    • 1/4″

    Pin Punches work with any standard 1/4″ Driver and are machined from solid bar stock.

  • Insite Arms Barrel Tuner – 1/2×28″ Muzzle Thread FOR USE WITH NO MUZZLE BRAKE – Designed for the Vudoo V22 – Black Nitride Only

    $200.00 Read more

    Barrel Tuners have solidified their place in the Benchrest and F-Class disciplines. Tuners are now being recognized as a valuable tool in when group size has potential for improvement especially when the shooter is limited to Factory Ammunition or a specific load or bullet selection.

    The Insite 1/2×28 Vudoo Tuner will work with a muzzle thread of 1/2×28″ – No Brake Required. The set screws engage only a flat portion of the collar. Our design allows proper position of the crown flush with the rear wall of the first port. This avoids accuracy degrading turbulence which occur when shrouding the crown in a “tunnel” before gasses can discharge from the first port.

  • Sale!

    FIX IT STICKS Magnetic Patch

    $11.19 Add to cart

    Magnetic Patch.

    • Easy way to keep track of loose screws / bits when in the field.
    • Magnetic patch attaches to front of Fix It Sticks Deluxe Case via Velcro.
    • Velcro on the front allows patches to be attached.
    • Patch can be used directly on case, or flipped over and used as a tray.
  • 4 Inch LBS Miniature Torque Limiter & Three Bit Combo Pack

    $69.99 Add to cart

    Level your optics with machined aluminum levels, featuring precise UK-sourced bubble vials Kit includes: Magnetic level NATO/Pic rail level/anti-cant device Protective foam carrier with pouch.

  • Fix It Sticks Bench Kit

    $499.00 Read more

    Fix It Sticks Bench Top Kit

    A full range of Torque Limiters for Home or Shop use.

    Includes:

    • T-Handle Driver
    • Fourteen Torque Limiters (6, 10, 15, 20, 25, 30, 35, 40, 45, 49, 55, 60, 65, and 80 inch lbs)
    • Molded Plastic Storage Base that holds T-Handle, Nineteen Torque Limiters, and Forty Eight 1/4″ Bits.

              NOTE:  Bits are not included

     

  • Sale!
  • Fix It Sticks Deluxe Case

    $34.99 Add to cart
    Fix It Sticks Deluxe Case.  Has a molded bit holder that runs along the bottom that holds 16 Bits, 1/2″ Socket, and 4 Torque Limiters.  Sewn loops hold Fix It Sticks or T-Way Wrench, as well as additional Torque Limiters or Components.
    Velcro on Front, and MOLLE Webbing on back.
  • Insite Arms Barrel Tuner - For 1.125" Heathen 3/4 x 24 , 18x1, 3/4x20 thread Black Nitride

    Insite Arms Barrel Tuner – For 0.995″ Heathen 5/8×24 thread Black Nitride

    $200.00 Add to cart

    Barrel Tuners have solidified their place in the Benchrest and F-Class disciplines. Tuners are now being recognized as a valuable tool in when group size has potential for improvement especially when the shooter is limited to Factory Ammunition or a specific load or bullet selection.

    The Insite Tuner will work with any of the 1.125″, 0.995″ & 0.885″ Heathen Brakes, without tools or gunsmith modification. The tuner does not touch the barrel or the brake body – only the lock collar/nut. The Tuner is supplied with a replacement “outside-threaded” locking collar / jam-nut for the muzzle brake. The set screws engage only a flat portion of the collar. Our design allows proper position of the crown flush with the rear wall of the first port. This avoids accuracy degrading turbulence which occur when shrouding the crown in a “tunnel” before gasses can discharge from the first port. The tuner can be removed and the Heathen brake run alone in just seconds if the Insite Tuner is not needed or required. The Heathen locking collar requires no tools – hand tight is nearly always sufficient especially on most custom rifles with true threads and square shoulders.

     

  • FIX IT STICKS REPLACEABLE VERSION - SHOOTING & HUNTING EDITION W/ BRACKET  FISRSH16

    FIX IT STICKS REPLACEABLE VERSION – SHOOTING & HUNTING EDITION W/ BRACKET FISRSH16

    $49.99 Add to cart

    The Fix It Sticks Replaceable Edition Shooting / Hunting offers unmatched portability, functionality and versatility.  Two Fix It Sticks (which combine to form a T-Handle) and 16 bits are held in a molded bracket for portability / storage.  Extra room on each end can hold two additional bits.

    Replaceable Set includes two sticks, bracket, and 16 different bits:

    • 2.5mm hex
    • 3mm hex
    • 4mm hex
    • 5mm hex
    • T-10
    • T-15
    • T-20
    • T-25
    • T-30
    • 1/8″ Hex
    • 5/64″ Hex
    • 3/32″ Hex
    • 5/32″ Hex
    • 3/16″ Hex
    • Slotted #5
    • Phillips #1

    The ultimate gun maintenance tool. Take the shop tool experience with you on the road.

    • High quality steel construction (can withstand 40Nm of Torque)
    • Compact
    • Durable
    • Accepts any standard 1/4″ bit
    • Weight: 116 grams
  • FIX IT STICKS Small Torque Limiter 20 INCH LBS FISTL20

    $54.99 Add to cart

    Torque Limiter prevents over-tightening of fasteners

    When Inch Lbs is reached:

    • Audible “Click” is heard.
    • Limiter “spins” preventing further torque from being applied.

    Features

    • Accepts any standard 1/4″ bit
    • Fits into any standard 1/4″ driver
    • +/- 6% Accuracy
    • Retains accuracy for 20,000 cyclesIntegrates perfectly with Fix It Sticks Replaceable Edition for field / travel use.Integrates perfectly with T-Way Wrench for shop use.
  • Sale!

    FIX IT STICKS BENCHTOP BIT PACK

    $64.00 Add to cart

    Description

    The benchtop bit pack covers all of your fix it needs with bits to help turn just about any fastener you can find.  Assortment fits the Benchtop Tray

    1/4″ Electroless Nickel Plated Hex Bits (43)
    • Phillips: 0, 1, 2(x2), 3
    • Slotted: 3mm, 4,mm 5mm, 6mm, 7mm
    • SAE Hex: 0.050″, 1/16″, 5/64″, 3/32″, 7/64″, 1/8″, 9/64″, 5/32″, 3/16″, 7/32″, 1/4″, 5/16″
    • Metric Hex: 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 5.5mm, 6mm, 8mm, 10mm
    • Torx: 6, 8, 10, 15, 20, 25, 27, 30, 35, 40, 45

  • Fix It Sticks LONG RANGE COMPETITION TOOLKIT with ALL-IN-One Torque Driver

    $389.99 Add to cart

    Precision is the name of the game in long-range shooting, and Fix It Sticks’ Long-Range Competition Toolkit will help you keep your high-performance rifle in peak running condition while in the field.

    Use this comprehensive assortment of tools in even the most austere conditions. With it, you can tighten down your optics, action and accessories to the correct torque to ensure precise round placement, shot after shot.

    The Long-Range Competition Toolkit includes:

    • Ratchet T-Handle w/Locking Hex Drive
    • 15, 25, 45, 65 in-lbs torque limiters or All-In-One Torque Driver
    • 1/2″ Socket/Adapter
    • Mini Pry Bar
    • Pin Punch Set (1/16″, 3/32″, 1/8″, 5/32″, 3/16″, 1/4″)
    • Bronze Scraper
    • Steel Pick
    • Cleaning Brush Bit
    • Set of two 8-32 adapters
    • Machined Aluminum Bubble Level Set, which includes: magnetic level & rail clamp level/anti-cant device with precise UK-sourced bubble vials
    • Stainless Steel Rod Set (6) with .223/6.5/.30 Brass Adapters & Ball Bearing Drive (locks into T-handle, assembles to 44″)
    • 3/16″ Extended Action Bit
    • 5/32″ Extended Action Bit
    • 24 Chrome Plated Bits: T8, T10, T15, T20, T25, T27, T30, P1, P2, [Hex 0.050″, 5/64″, 3/32″, 1/8″, 7/64″, 9/64″, 5/32″, 3/16″, 1/4″, 2.5mm, 3mm, 4mm, 5mm] [Slotted 3/16″, 3/32″]
    • Magnetic Velcro Patch
    • Micro Fiber Lens Cloth
    • Torque Value Reference/Conversion Card
    • Soft Carrying Case with molded, low-profile bit holders designed to hold any bit / accessory with a standard 1/4″ Base
  • Fix It Sticks EXTENDED ACTION BIT PACK – 6 BITS

    $59.99 Add to cart

    Custom ball end hex bit designed to tighten hard to reach screws.

     

     

     

     

    • Choose 3/16″ for Remington 700, AICS, etc.
    • Choose 5/32″ for Ruger 10/22 V-Block, etc.
    • Choose 5/64″ for general use
    • Choose 1/8″ for KIDD, etc.
    • Choose 5mm for Action Screws
    • Choose T30 for numerous Precision Rifles (T30 is not a Ball End)
    • Shaft of bit is 0.1875″ X 4.0″ long for hard to reach screws.
    • Works with any standard 1/4″ bit driver
  • Fix It Sticks 65, 45, 25 & 15 INCH LBS KIT WITH DELUXE CASE, T-HANDLE, AND EXTENDED BIT FISTLS11-T-EB316

    $255.00 Read more

    Kit includes:

    • 65 Inch Lbs miniature torque limiter
    • 45 Inch Lbs miniature torque limiter
    • 25 Inch Lbs miniature torque limiter
    • 15 Inch Lbs miniature torque limiter
    • T-Way T-Handle Wrench
    • 16 different bits: T10, T15, T20, T25, T30, P1, slotted 5mm [hex 5/64, 3/32, 1/8, 5/32, 3/16, 2.5mm, 3mm, 4mm, 5mm]
    • 1/2″ Socket and 1/4″ bit adapter set
    • Deluxe Zippered pouch
    • Extended 3/16″ Ball End Hex bit designed to reach the action screws of such Chassis systems as JAllen, Accuracy International, Remington 700, and Masterpiece Arms.
Shopping Cart

Active filters

Subscribe, Save & Win!

Subscribe to our email newsletter and you will be the first to hear about our sales, contests and giveaways!