Filter
  • Gray Ops CNC MasterPiece Arms BA Comp Side Rail Weights - Steel

    Gray Ops CNC MasterPiece Arms BA Comp Side Rail Weights – Steel

    $174.00 Add to cart

    PURPOSE

    • Give the perfect balance point to your MPA BA Comp/Matrix/ESR Chassis when combined with the MPA Competition Side Rails
    • Added weight Reduces recoil and adds stability
    • Added locations for hand gripping

    FEATURES

    • Machined from 1018 cold rolled steel
    • Black Nitride finish for superior corrosion and rust resistance
    • Includes 4 weights (two weights per side)
    • Each weight has 3 built in flush cup locations (12 total per kit) for each sling and accessory attachment
    • Adds 27.4 ounces per 4 weight kit
    • BA Comp Kit Dimensions roughly 0.6 x 0.6 x 5.25”
    • Matrix/ESR/Matrix PRO Kit Dimensions roughly 0.5 x 0.6 x 6”
    • Hardware to attach to side rails included

    NOTE

    • Side rails (shown in picture) purchased separately from MPA website must be installed to utilize these weights
  • ATLAS BT28: AFAR Rail Kit

    $53.90 Read more

    The BT28 AFAR Rail Kit will mount into accessory rails and provide a low profile 1913 Picatinny rail for attaching the Atlas Bipods or other accessories. This is a great option for shooters that have accessory rails and want to use their rail mounted Atlas on several rifles.

    The uniquely designed rectangle nuts (BT28-N) fit both Freeland and Anschutz style rails by rotating them 90°.

    The 1913 Picatinny Rail is 2.05″ long and has a center to center spacing of 1.6″ with a 1.00″ radius back.

    Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish with 4041 Alloy Steel fasteners. Includes two rectangle nuts, two 3/8″ fasteners and two 1/2″ fasteners. Available in black only.

    • Length: 2.05″
    • Weight: 0.89 ounces
  • Gray Ops MPA Matrix PRO – Internal Weight Kit

    $234.99 Read more

    PURPOSE

    • Add weight forward of the magazine for better balance
    • Increase weight for added recoil reduction and spotting shots

    FEATURES

    • Machined Steel
    • Black Nitride finish for corrosion/rust protection
    • Includes 8 total weights (7 Regular/1 Contoured to accept Spigot mount)
    • Includes Stainless Steel hardware
    • Kit adds 30 ounces for forend
    • 6 threaded holes per weight to allow location flexibility
    • Installs without removing barreled action from chassis
  • Fix It Sticks Bit Extension

    $19.99 Read more

    Fix It Sticks Bit Extension that can be used with our T-Handle Wrenches for hard to reach screws and fasteners.

    • 3.5 Inches in Length (not including male hex portion)
    • Magnetic end accepts any standard 1/4″ Bit
  • HRD GEAR 6MM MAGAZINE SPACER KIT & AIAW Double Stack Magazine Package

    $189.99 Read more

    The HRD GEAR 6mm magazine spacer kit is designed to make the popular 6BR case and it’s variant cases run flawlessly in the AW/AX magazines (part numbers 0726 and 6677).  The back spacer is a press fit and clips into place from the top of the mag. There is a small hole to aid in removal of the back spacer (the tip of a bullet fits perfectly).  THERE ARE NO TOOLS OR MODIFICATIONS NEEDED OR REQUIRED TO INSTALL THIS SPACER KIT.

    Also Included:

    Accuracy International factory mags for short action 308 AW/AWP and AT rifles.  These are 10 round, double stack, double feed magazines.

     

    Model: AW Rifle/AT Rifle Or Custom Action Able to accept AW Mags ( ie. not factory 700 actions with integrated feed lips )

    Caliber: .308 Win Family, 6/6.5 CM, BR/Dasher etc..

    Capacity: 10 Round

    Material: Steel

    Finish: Matte Black

    Firearm Fit: Short Action

  • Gray Ops Harris Bipod QDA

    $84.99 Read more

    PURPOSE

    • The Quick Detach Adapter allows a Harris notched leg bipod to use Atlas style feet/accessories. Different style feet can be changed out in seconds with no tools required.  Perfect for competition or hunting scenarios where you must adapt to the specific task at hand.
    • Eliminates the need to carry multiple bipods

     

    FEATURES

    • Machined from 6061 Aluminum and Hard Black Anodized
    • Set screw allows for a rigid, “no wiggle” lock-up on your Bipod
    • Remove your atlas foot/accessory quick and easy with the spring loaded button
    • Adds approximately 1” total height to the bipod
    • Allen wrenched included for easy installation
  • Tab Gear Biathlon Sling with Flush Cups Reg Buckles

    Tab Gear Biathlon Sling with Flush Cups Reg Buckles

    $169.99 Select options This product has multiple variants. The options may be chosen on the product page

    The solution to carrying a heavy rifle for long distances.

    The padded shoulder straps distribute the weapon’s load to both shoulders, instead of one, resulting in less shooter fatigue after long periods of travel. Having the load centered on the back aids in maintaining better balance when using two hands for other tasks such as carrying a primary weapon, or navigating steep terrain.

    The integrated shooting loop (available on the Regular and Elite models) can be deployed to allow the shooter to rapidly sling up for much steadier positional shooting.

    Both straps are easily adjustable and utilize a buckle to make the sling fast and easy to remove if necessary.

    The biathlon slings do not require a conversion kit in order to fit it to different rifles.  You will need to just have additional attachments to fit your stock.  So if you purchase a biathlon sling with Flush Cups and you have another rifle that requires HK hooks, you will just need to have a set of HK hooks.


     FEATURES / SPECS

    • 1.5″ Mil-Spec Webbing
    • 1 ½” Fastex buckles or Elite Cobra buckles
    • Elastic keepers secure adjustable strap ends
    • Water resistant 1000D Cordura® shoulder straps
    • Dual Layers of closed cell, waterproof, foam in the shoulders provide comfort and support
    • User adaptability, shooter can change out swivels to fit different weapon systems
    • Adjustable loop for shooting support (not available in Simple Sling)
    • Made in Texas with US made materials!
    • Lifetime Warranty
  • ATLAS BT23 Ski Feet

    ATLAS BT23 Ski Feet

    $80.90 Add to cart

    BT23: Atlas Ski Feet

    The BT23 Atlas Ski Feet are easily installed to any V8, PSR or CAL model Atlas Bipod with the press of a stainless steel plunger. They will lay flat in the 90 degree position only. The BT23 deliver a fully articulated smooth foot to support the bipod. Sold as a pair. Available in black only. NSN 1005-01-640-8881

    Weight: 1.5 ounces

    Product will work on V8, PSR and CAL models only.

  • BT46-NC PSR Atlas Bipod: Standard height

    BT46-NC PSR Atlas Bipod: Standard height

    $391.40 Add to cart

    BT46-NC PSR Atlas Bipod: Standard height No Clamp

    The BT46-NC PSR (Precision Sniper Rifle) Atlas Bipod “No Clamp” model has a two hole pattern of 1.100” with the holes being 10/32 threads. It requires any 17S size lever style mount to include the ADM-170-S, ARMS 17S, TRAMP from Badger Ordnance, LT271 or any ARCA dovetail mount with the same hole pattern. The BT46-NC will also mount directly our BT19 AI Spigot or BT70 M-LOK® Adapter.

    It is comprised of 6061-T6 aluminum, except the strengthened inner legs which are made from 7075-T6 aluminum that are Mil-Spec Type III hard coat anodized and have heat treated, stainless steel components. Includes two 10-32 x 3/8″ flathead socket screws. Available in black only.

    The PSR series of Atlas Bipods were developed for the SOCOM PSR (Precision Sniper Rifle) Weapons System (BT46-LW17 was selected for SOCOM PSR).

    • Height Range: 5 – 9.4″ (6.5” at 90°)
    • Preloaded Pan: 30 degrees
    • Preloaded Cant: 30 degrees
    • Position Button 0.5″ diameter
    • Fore and Aft pivot limiting Bosses
    • 5 leg positions: 0, 45, 90, 135 & 180 degrees
    • Non-Rotating Legs: outer leg does not rotate around inner leg
    • Larger, stronger inner legs
    • Weight: 11.42 ounces approx.
    • Footprint: 8–11″
  • WCD Kydex Vudoo V22 Mag Carrier – Walsh Custom Defence Carbon Fiber Color

    $59.99 Read more

    Our WCD Vudoo/B14 Kydex Mag Holsters are custom made and are designed to be used with Vudoo and Bergara B14 22 LR magazines. Each holster has an open bottom with a rubber stop which keeps the ammunition protected inside of the holster, fully adjustable tension and comes with a 1.5” or 1.75” belt clip which are made in the USA. A genuine Blade-Tech Tek-Lok belt clip is also available for $15 each. Several color options available. Other colors available upon request.

    Please Note: For both left and right side carry positions, the bullet tips will be facing forward while magazine is in the holster

    NOTE: Standard Belt Clips accommodate belts up to 1/4” thick

    NOTE: We recommend adding Teflon tape or blue Loctite to all bushing/tension screws once desired tension is set to prevent screws from backing out during use

  • Insite Arms Barrel Tuner - For 1.125" Heathen 3/4 x 24 , 18x1, 3/4x20 thread Black Nitride

    Insite Arms Barrel Tuner – For 0.885″ Heathen 5/8×24 thread Black Nitride

    $200.00 Add to cart

    Barrel Tuners have solidified their place in the Benchrest and F-Class disciplines. Tuners are now being recognized as a valuable tool in when group size has potential for improvement especially when the shooter is limited to Factory Ammunition or a specific load or bullet selection.

    The Insite Tuner will work with any of the 1.125″, 0.995″ & 0.885″ Heathen Brakes, without tools or gunsmith modification. The tuner does not touch the barrel or the brake body – only the lock collar/nut. The Tuner is supplied with a replacement “outside-threaded” locking collar / jam-nut for the muzzle brake. The set screws engage only a flat portion of the collar. Our design allows proper position of the crown flush with the rear wall of the first port. This avoids accuracy degrading turbulence which occur when shrouding the crown in a “tunnel” before gasses can discharge from the first port. The tuner can be removed and the Heathen brake run alone in just seconds if the Insite Tuner is not needed or required. The Heathen locking collar requires no tools – hand tight is nearly always sufficient especially on most custom rifles with true threads and square shoulders.

     

  • Nightforce X-Treme Duty™ Ultralite™ Rings 30mm HIGH 4-screw A107

    Nightforce X-Treme Duty™ Ultralite™ Rings – 4 Screw

    $226.00$253.00 Select options This product has multiple variants. The options may be chosen on the product page

    X-Treme Duty™ Ultralite™ Rings are crafted of machined 7075-T6 hard anodized aluminum, with titanium cross bolts and jaws, and 4 titanium screws. This craftsmanship gives you the performance of steel at half the weight.

  • MasterPiece Arms ( MPA ) Cheek Riser Pad

    $13.99 Read more
    Product Details

    This is a replacement Cheek Riser Pad. Self Adhesive and Laser Engraved with MPA Logo.

  • Fix It Sticks FIX IT STICKS MINI FLASHLIGHT

    Fix It Sticks FIX IT STICKS MINI FLASHLIGHT

    $29.99 Add to cart

    Have a miniature light in your Fix It Sticks case.

    Mini Flashlight

    • Great for finding small parts in the dark or for Bore Inspection
    • Twist on / off operation
    • Batteries Included (Four LR41)
    • Integrates perfectly with Fix It Sticks Replaceable Edition and T-Way Wrench.
  • Fix It Sticks 65, 45, 25 & 15 INCH LBS KIT WITH DELUXE CASE, T-HANDLE, AND EXTENDED BIT FISTLS11-T-EB316

    $255.00 Read more

    Kit includes:

    • 65 Inch Lbs miniature torque limiter
    • 45 Inch Lbs miniature torque limiter
    • 25 Inch Lbs miniature torque limiter
    • 15 Inch Lbs miniature torque limiter
    • T-Way T-Handle Wrench
    • 16 different bits: T10, T15, T20, T25, T30, P1, slotted 5mm [hex 5/64, 3/32, 1/8, 5/32, 3/16, 2.5mm, 3mm, 4mm, 5mm]
    • 1/2″ Socket and 1/4″ bit adapter set
    • Deluxe Zippered pouch
    • Extended 3/16″ Ball End Hex bit designed to reach the action screws of such Chassis systems as JAllen, Accuracy International, Remington 700, and Masterpiece Arms.
  • Gray Ops Ckye-Pod Clamp Adapter

    Gray Ops Ckye-Pod Clamp Adapter

    $58.99 Add to cart

     

    PURPOSE:

    • Replaces Ckye-Pod clamp making it universal to all Atlas compatible clamps

    FEATURES:

    • Machined from 6061 Aluminum
    • Hard black anodizing
    • Includes shorter brass tipped panning set screw
    • Adds 0.3125” in height
    • Hole machined on bottom to accept the “pan-lock” some versions of Cyke Pod have

     

    Installation:

    • Remove existing clamp by loosening set screw on back of bipod
    • Pull the clamp off the bipod and save the pull stud and wave washer
    • Install the wave washer and pull stud into adapter
    • Re-install adapter onto bipod by tightening the set screw on the bipod
    • Make sure not to overtighten the pan-lock brass tipped set screw (very minimal pressure needed)
    • Install Atlas compatible arca clamp

     

  • FIX IT STICKS 15 INCH LB Limiter& 5/32 Extended Ball Head – for Ruger 10/22 Rifles

    $54.99 Read more

    Ruger 10/22 torque limiter with extended 5/32″ Ball-End Hex that is designed to reach the V-Block screws of Ruger 10/22.  Also may be used to tighten the action screw.

    When 15 Inch Lbs is reached:

    • Audible “Click” is heard.
    • Limiter “spins” preventing further torque from being applied.

    Designed for Ruger 10/22 V-Block screws.

    Features

    • Accepts any standard 1/4″ bit
    • Fits into any standard 1/4″ driver
    • +/- 6% Accuracy
    • Retains accuracy for 20,000 cycles

      Integrates perfectly with Fix It Sticks Replaceable Edition for field / travel use.

      Integrates perfectly with T-Way Wrench for shop use.

              NOTE:  T-Handle wrench is not included.  Only the torque limiter and bit.

  • Hawkins Precision Ultra-Light Tactical Scope Rings 30mm Low 0.885 Height

    $239.00 Read more
    Ultra-Light Tactical Scope Rings

    Ultra-light tactical scope rings from Hawkins Precision are made in the USA out of billet 6061 T6 aluminum. These fully machined rings are robust and feature a corrosion-resistant black anodized finish. Machined with a clamp and recoil lug made from 7075 aluminum, these scope rings deliver extra strength and grip. The ultra-light design frees you from carrying unnecessary bulk. Hawkins Precision scope rings come standard with an anti-cant level cap and are available in 30mm, 34mm and 35mm, sized in low, medium, and high. Rings can be ordered with a center anti-cant level, or an offset level.

    Torque Specs: 25 in-lbs ring caps / 65 in-lbs cross bolts

     
    size
    Measurement from Picatinny Rail to optical center
    30mm 34mm 35mm Application
    low .885″ * * 50mm objective with standard barrel contours
    medium 1.0″ * * 56mm objective with standard barrel contours
    high 1.25″ * * 50mm objective with AR style front forend
    X high 1.375″ * 56mm objective with AR style front forend
  • 1 Set of Fix It Sticks, 65 & 25 Inch lbs Torque Limiters, 16 Bits, 1/2″ Socket & 1/4″ Bit Adapter, Deluxe Case FISTLS11

    $169.99 Read more

    This Fix it Sticks set comes with 65, 45, 25 and 15 inch lbs torque limiters. It also includes 16 bits, a 1/2″ Socket, 1/4″ bit adapter and a Tactical Tailor Deluxe Case. The “T-Handle” shown in the image is NOT a permanent T-Handle but two “sticks” that fit together to make a T-Handle and come apart to fit in the case for easy storage.

  • Rangefinder Extension Adapter GRAY OPS CNC

    $94.99 Read more

    NOTES:

    Designed for rangefinders/optics without the anti-rotate pin
    This product requires a 4-side dovetail adapter to be ARCA mounted. Can still be mounted to non-arca tripods via ¼-20 threaded hole in bottom
    Some pictures shown with optional adapter

    PURPOSE:

    Allows 3” of extra optic/accessory travel
    Moves optic closer to edges of AMP Plates

    FEATURES:

    Machined from 6061 Aluminum
    Type II Black Anodizing
    Includes sliding ¼-20 captive screw
    Extra ¼-20 threaded hole in bottom for different attachment methods

  • Lapua 4PH6010: 6.5×47 Lapua Cases 100/Box

    $179.00 Read more

    Lapua LU4PH6010 6.5×47 Lapua Cases 100/box

    The base, body and neck of the Lapua cases have been designed to maintain exact tolerances over multiple reloading cycles. Advanced metallurgical research and manufacturing techniques ensure that Lapua cases are leaders in uniformity and quality.
    The most precise cases on the market

    Lapua cases are the best in the world. The marksmen themselves think this way. The .220 Russian, for example, is the number one choice of the best benchrest shooters all over the world. All our cases are strong and uniformly precise.
    Lapua cases are manufactured to be reloaded, again and again, dozens of times.
    Case construction
    Base
    The base section is hard and strong, and the dimensions remain constant and will hold primers tight in primer pocket even after repeated reloading.
    Body
    The brass body section is hard and firm. It is easy to extract after firing, whether full sizing or only neck sizing was used in reloading.
    Neck
    Strict tolerances in concentrity and wall thickness are used in manufacturing. The neck and shoulder are annealed to withstand repeated reload

Shopping Cart

Active filters

Subscribe, Save & Win!

Subscribe to our email newsletter and you will be the first to hear about our sales, contests and giveaways!